Difference between revisions of "Ed Powell"
From WLCS
Line 17: | Line 17: | ||
'''Parts:''' | '''Parts:''' | ||
* The following parts will be used: | * The following parts will be used: | ||
− | ** Protoboard | + | ** [http://www.radioshack.com/product/index.jsp?productId=2102843&filterName=Type&filterValue=Breadboards| Protoboard] |
** Atmel AVR Atamega16 micro-controller | ** Atmel AVR Atamega16 micro-controller | ||
− | ** Programmer for the | + | ** Programmer for the micro-controller |
− | ** 64 | + | ** 64 green [http://www.superbrightleds.com/cgi-bin/store/index.cgi?action=DispPage&Page2Disp=/specs/G16120_specs.htm| LEDs] |
− | ** | + | ** 1 green (above) and 1 [http://www.superbrightleds.com/cgi-bin/store/index.cgi?action=DispPage&Page2Disp=/specs/R12120_specs.htm| red] status LED |
− | ** 16 220 | + | ** 16 [http://www.radioshack.com/product/index.jsp?productId=2062317&filterName=Type&filterValue=1%26amp;amp;%23047;2-watt+resistors| 220 ohm resistors] for LEDs |
− | ** 2 470 ohm resistors | + | ** 2 [http://www.radioshack.com/product/index.jsp?productId=2062320&filterName=Type&filterValue=1%26amp;%23047;2-watt+resistors| 470 ohm resistors] |
− | ** 1 10k resistor | + | ** 1 [http://www.radioshack.com/product/index.jsp?productId=2062330&filterName=Type&filterValue=1%26amp;%23047;2-watt+resistors| 10k resistor] |
− | ** 4 2.2 k resistors | + | ** 4 [http://www.radioshack.com/product/index.jsp?productId=2062325&filterName=Type&filterValue=1%26amp;%23047;2-watt+resistors| 2.2 k resistors] |
− | ** 4 | + | ** 4 [http://www.radioshack.com/product/index.jsp?productId=2062586&filterName=Type&filterValue=Transistor| 2N2222 transistors] |
− | ** 6 0.1uF ceramic capacitors | + | ** 6 [http://www.radioshack.com/product/index.jsp?productId=2062365&filterName=Type&filterValue=Ceramic+disc+capacitors| 0.1uF ceramic capacitors] |
− | ** 2 22pF ceramic capacitors | + | ** 2 [http://www.sparkfun.com/products/8571| 22pF ceramic capacitors] |
− | ** 1 | + | ** 1 [http://www.sparkfun.com/products/669| 14.7456 MHz crystal] |
− | ** 2 tactile buttons | + | ** 2 [http://www.radioshack.com/product/index.jsp?productId=3060978 |tactile buttons] |
** Power switch | ** Power switch | ||
** Connector for 5v power | ** Connector for 5v power | ||
+ | ** [http://www.radioshack.com/product/index.jsp?productId=2062605| 40 pin connector for micro-controller] | ||
Revision as of 10:28, 17 February 2011
3rd Quarter Proposal
Description:
- The instruction set to program the micro-controller will be learned from the PDFs of the Atmel website and from some of the linked websites
- The soldering of the cube will be finished
- The cube code will be written using the programming software
- It will be tested for bugs and brought into class to be finalized
Progress:
- All of the necessary parts to build the cube have been bought - Done
- Enough C has been learned to be able to to program the micro-controller - Done
- The parts have been soldered onto the protobaord and are ready to be programmed - Almost done (just the connections to the micro-controller are remaining)
- The instruction set to program the micro-controller has been learned - Ongoing
- The cube has been tested -
Parts:
- The following parts will be used:
- Protoboard
- Atmel AVR Atamega16 micro-controller
- Programmer for the micro-controller
- 64 green LEDs
- 1 green (above) and 1 red status LED
- 16 220 ohm resistors for LEDs
- 2 470 ohm resistors
- 1 10k resistor
- 4 2.2 k resistors
- 4 2N2222 transistors
- 6 0.1uF ceramic capacitors
- 2 22pF ceramic capacitors
- 1 14.7456 MHz crystal
- 2 |tactile buttons
- Power switch
- Connector for 5v power
- 40 pin connector for micro-controller
2nd Quarter Proposal
Description:
- Continue working on the 1st quarter project by learning C to program the micro-controller
- There will be more websites used this quarter with more concise information on programming the micro-controller
- If more websites are found during the quarter they will be added to this page
- Description from the previous quarter should be read for more information on the project
- Two books (C for Unix and C++ for You++) will also be used along with the websites to help accomplish this task
- The goals and deadlines may be altered if more resources are found during the quarter
- There will be more websites used this quarter with more concise information on programming the micro-controller
Resources and Information:
- Installing the Software on the Micro-Controller
- 5x5x5 LED Cube Instructable
- ATmega16 Programming Guide
- ATmega Architecture Guide
- ATmega32 Programming Guide
- AVR Programming Guide
- AVR C Programming Guide
Goals and Deadlines:
- Work through all steps in the C Programming website by 11/19/10
- This should be completed at home by the date above
- After each step is competed a program containing what was learned should be written
- Work through all of the steps in the ATmega16 programming guide by 12/6/10
- Two steps of the guide should be done per class period
- What was learned the last class period should be reviewed the next class period so it is not forgotten
- Start working with the micro-controller by installing and running beginner programs to understand how it works
- The tutorials above should be used to learn how to program the controller
- The installation and testing will only be done at home but the code may be written at school
- A separate board may be created for this purpose
- Program the micro-controller with the finished code and make sure that it works
- After figuring out how the micro-controller works the writing of the final code should begin
- This may be done at school or at home
- The finished cube should be brought to class
Progress:
- The C Programming website has been completed and program files for each section have been written - Done
- The parts necessary to build the cube have been ordered or gotten - Done
- The programming process for the ATmega16 miro controller has been learned - Done
- The code to program the micro-controller has been learned -
- Writing of the final code for the cube has begun -
1st Quarter Proposal:
Description:
- Build a single color LED cube using the following parts:
- Acrylic Case
- Protoboard (the type with copper circles)
- Atmel AVR Atamega16 micro-controller
- Programmer to program the Atmega16
- 64 LEDs
- 2 status LEDs
- Max232 rs-232 chip, or equivalent
- 16 resistors for LEDs
- 2x resistor 470 ohm
- 1x resistor 10k
- 4x resistor 2.2k
- 4x NPN transistor BC338
- 1x 10uF capacitor
- 1x 1000uF capacitor
- 6x 0.1uF ceramic capacitor
- 2x 22pF ceramic capacitor
- 1x crystal 14.7456 MHz
- 2x tactile button
- Optional power switch
- Connector for 12v power
- Optional connector for 5v power
- Learn C to program the micro-controller using the C Programming Guide
Resources and Information:
- 4x4x4 LED Cube Instructable
- LEDs
- RGB LED Cylinder
- Think Geek Cube Available to Buy
- RGB LED Cube Story|RGB LED Cube Story
- RGB LEDs
- RGB LED Cube Story Cube For Sale
- 8x8x8 RGB LED Cube
- RGB LED Cube Directions
- RGB LED 4x4x4 Cube Directions
- C Programming Guide
Goals and Deadlines:
- Acquire all parts necessary for the cube by 10/1/10
- Solder parts on to the protoboard by 10/7/10
- Bend and attach all LEDs to the board by 10/14/10
- Finish assembling the cube by 10/15/10
- Learn C by 10/21/10
- Program the micro-controller by 11/1/10
Possible Later Goal:
- Build an RGB LED cube after the single color cube is finished using the following parts (if deemed possible):
- Acrylic Case
- H4C printed circuit board
- 110VAC to 9VDC 300mA transformer
- 22 AWG straightened galvanized soft steel wire x40
- Diffuse common-cathode RGB LED x64
- PIC18F4620 micro-controller (40 pins)
- SN74AHC574 octal D-type flip-flop x4 (20 pins)
- ULN2803A NPN Darlington transistor array (18 pins)
- LM2574 5V switching regulator (8 pins)
- 22 resistor array (16 pins)
- 47 resistor array (16 pins)
- 68 resistor array (16 pins)
- 47K resistor x3 (yellow-violet-orange-gold)
- 1K resistor x5 (brown-black-red-gold)
- 1N4148TR signal diode x24 (red)
- 511-BAT48 rectifier diode (blue)
- 330mH inductor
- 0.1uF ceramic capacitor x5
- 10uF electrolytic capacitor
- 22uF electrolytic capacitor
- 220uF electrolytic capacitor
- 6” black wire
- 18” red wire
- 24” white wire
- 2.1mm DC power jack
- Toggle switch
- Momentary toggle switch x2
- 1” threaded standoff x4
- 1⁄2” 4-40 screw x8
- Rubber feet x4
- DLP-UB232R UART-USB bridge module
- Mini-B USB cable